Balloon flight Payload Recovered

High Altitude Balloon Success. Payload Recovered.Andy PS1 Preparing to fly

Jason and I went to Deniliquin NSW (Australia) to help a good friend, Andy from Melbourne, launch and recover a high altitude balloon / payload. I am part of Team Stellar going for the Google Lunar X-Prize (GLXP). I am in charge of Communications, Tracking and Data. Jason (11) is their Australian Student Representative. Jason and I have launched and recovered 16 payloads to date and assisted with others and we love High Altitude Balloons (HABs).

I brought my fellow Team Stellar member, Tim Blaxland and his son Rhys (9) along for the experience. Tim is Stellar’s chief of Navigation. The launch was at Deniliquin and we traveled part of the way there on Friday and the rest early on Saturday morning to be there for a 9:30 start. It was an 8 hour drive and we intended to do another 8 hours back later on Saturday after we recovered the payload.

Fellow HAB enthusiast Todd Hampson also traveled from Sydney in his own vehicle. it was great that we all arrived at the designated point in a timely fashion and started the final preparations for launch. Other than Tim and Reece, we all have Amateur Radio licenses and on this flight we would have 2m APRS tracking system. See earlier posts about APRS. In addition there was also RTTY on UHF. The RTTY system s available for non amateur radio hobbyists to use.

Andy had a video camera camera hooked up to a Raspberry Pi unit. Its job was to break up the video into smaller packets of data and send it along with the RTTY GPS information. The pictures are then sent to a server on the internet and the packets reassembled into a complete picture if all of the packets are received. The transmitter is very low powered and many people set up their equipment to help receive and download the images. Below is an image from the flight. The grey strips are missing packets that no one managed to receive successfully.

Note that at this time of the year, the wheat and other crops  have been harvested and the temperatures are in the 40C range at times. With little rain, the fields are a brown cover. The dark areas are either farms with crops still growing or trees around the rivers that flow through the region.

Andy PS1 flight Deniliquin NSW
















The photo is only from a low resolution camera but the payload also carried a GoPro that took photos. The top image is a small section from the flight camera while it was on the ground.

Here are the details that Andy distributed before the flight:

FYI, there will be a HAB launch from Deniliquin NSW this weekend, Sat 8th Feb 2014 at 11am EST.

 Payloads will be:
– SSDV RTTY 300baud, 450Hz shift, 8N1, 434.650Mhz (+- drift) USB, 25mW quarter-wave antenna
– APRS 1200b 145.175Mhz 100mW with dipole antenna
– Cutdown RTTY 100baud, 450Hz shift, 8N1, 432.220Mhz (+- drift) USB, 25mW downlink, quarter-wave antenna.
RTTY tracking will be on, callsigns PS and PSPI
SSDV images will be uploaded to, callsign PSPI
APRS tracking will be on, callsign VK3YT-11

The temperature was 42C / 108F for much of the day and UV protection was essential. Recovery was easy, so we did not have an issue with tracking through the forests looking for the payload.

The flight lasted around 2hrs 50mins, reached max altitude of 36,789m / 120,699ft / 22.9 miles  before the balloon burst and landed in a paddock.

The following images were transmitted whilst in flight:

2014-02-08--01-11-07-PSPI-8C9 2014-02-08--01-43-42-PSPI-8CB2014-02-08--02-04-48-PSPI-8CC





























































The last image was taken close to maximum altitude.

GoPro3 images in the next post. Below, the flight path from left to right. The tropospheric winds (Jet Stream) where pushing the balloon to the eastand the stratospheric winds blew us west . When the balloon burst, the winds eventually took us east again as we passed through the Jetstream.

The Flight PS1 Map The Flight PS1 terrain


Leave a Reply